英國GRIMM格林進口潛水回流泵 UK GRIMM Imported submersible return pump

英國GRIMM格林進口潛水回流泵概述： 

          進口潛水回流泵是在引進英國格林潛水?dāng)嚢铏C(jī)生產技術基礎上開發的新型產品，該泵為二級污水處理廠混合液回流、反硝化脫氮的專用設備，亦可以用于地面排水時抽凈化水；灌溉和控制水道系統；廢水處理過程中再循環或泥漿抽吸回路中需要微揚程、大流量場所。

英國GRIMM格林進口潛水回流泵結構： 

進口潛水回流泵采用導桿自動結合就位固定方式，滑行導桿支架作為水泵整體的部件之一，水泵的全部重量以及泵送時產生的推力全部作用在對接出口管路法蘭上。水泵、附件和電纜在正常水深的工況下，能長期連續工作而無滲漏現象。
進口潛水可上下方便地進行升降移動，檢查或維修人員無需進入池底。
該回流泵應為臥式單級結構，垂直單導軌、自耦式安裝。葉輪的設計采用無堵塞、防纏繞結構型式，通過固體顆粒直徑可達100mm，10kw及以下電機及泵體為同軸直連。
回流泵能自動穩固地與穿墻管聯接，并且能在導桿的引導下從池頂部滑動至穿墻管處就位。
該回流泵為整體設計，采用封閉式聯接和潛水型，水泵的所有組件包括電機可在水下連續運轉。
⑴葉輪：
葉輪應采用不銹鋼制造，且作動平衡試驗。葉輪與軸之間裝有鎖定裝置，用于防止運轉時松動，葉片設計為三片式，具有自清、免振功能，為水力平衡的無堵塞、不纏繞的拽后設計。
⑵導流筒：
為維持水力效率和減少能量消耗，在回流泵葉輪外周設置導流筒外，并控制葉輪外周與導流筒的間隙。
⑶軸與軸承：
回流泵和電機的軸是連續無間斷的軸。軸能承受漿式葉輪旋轉時產生的所有軸向和徑向載荷。葉輪的軸完全與泵送的介質隔離。
回流泵電機軸在永久潤滑的兩個軸承上轉動，內軸承為單列深溝球滾珠軸承，主軸承為一個球面滾珠軸承、其中內軸承滾珠軸承用于承擔徑向力，用于承擔所有軸向力的軸承由主軸承組成。
⑷泵軸的密封：
每臺回流泵有一個用于軸密封系統的油室，并配備有排油裝置和檢查螺孔。排油和檢查螺孔便于從外部進入，使換油工作更加簡便、易行。
每臺回流泵至少配有二道密封以便將水泵的各部分隔開。
葉輪輪毅與軸承之間設置二道密封，隔砂隔污以延長內圈機械密封的壽命并起到保護作用。
葉輪軸端的密封作為插入式的靜/動環雙重機械密封。密封在一個通過水力作用對重疊密封面以恒定速度進行潤滑的油室中運行。內外機械密封均為產品，以防止外界液體進入油室。內外機械密封都是各自獨立運行的。
該泵用于軸密封系統的油室從設計上防止過滿和留有油膨脹的空間，帶有防漏密封的注油孔和檢查孔是很容易從外部檢查和維修的。
⑸冷卻系統：
回流泵電機能被周圍介質充分冷卻，較大電機裝有外部冷卻套，利用泵送液體的背壓用作電機循環冷卻。
提升支架系統：
回流泵配有提升用吊架座和起吊柱。起吊葫蘆內配置制動裝置。
安裝提升支架系統包括每機一套的方導軌等，并有專用臂式起吊柱、手拉葫蘆。
導桿的剛性支承在兩端。提升鏈條包括一個聯接到水泵的提水環。
⑹自耦系統：
回流泵出水法蘭面與穿墻管出水法蘭為重力自動耦合，泵的效率考核包括出水穿墻管在內，耦合面之間密封、可靠，具有自清洗功能。自耦系統為出口硬封式，并有可靠的設計保障提升、下降時不會受到刮擦破壞。
英國GRIMM格林進口潛水回流泵使用條件： 
1、連續運行時，介質溫度不高于40℃；
2、介質PH值為6-9；
3、潛沒深度10m。
英國GRIMM格林進口潛水回流泵設備特點：
1、按微揚程大流量專門設計，效率高；
2、按抗堵塞、防纏繞專門設計，使用可靠；
3、采用的密封材料，可以使泵的安全連續運行10000小時以上；
4、結構緊湊，安裝、維修方便；

5、主機采用沖壓成型結構，體積小、精度高、耐腐蝕、無噪音；
6、產品設置漏電、漏水及電機過載等保護及報警裝置，確保產品的安全性與可靠性。

英國GRIMM格林進口潛水回流泵技術參數：

葉輪直徑：400-620mm
公稱直徑：400-600mm
電機功率：1.5-22kw
額定電壓：380V
額定頻率：50HZ
額定電流：4.1-76A
防護等級：IP68
絕緣等級：F級

英國GRIMM格林進口潛水回流泵使用范圍： 

          用于地面排水時抽凈化水；灌溉和控制水道系統；廢水處理過程中再循環或泥漿抽吸回路中需要微揚程、大流量場所。

UK GRIMM Imported submersible return pump summary:

       Department of imported wearable mine pump horizontal single suction multistage centrifugal pump, is the British Green in the integrated absorption of the current basis is successfully developed, the product has the advantages of high efficiency, cavitation performance, wide range of performance, the key is to smooth and reliable operation. The overflow parts are made of wear-resistant materials, and the friction pairs and the clearance parts of the overflow clearance are treated by special process. The utility model is suitable for conveying the muddy mine sewage and other liquids with physical and chemical properties similar to water, and is the most ideal water lifting equipment for coal, mining, metallurgy and other industries.

UK GRIMM Imported submersible return pump structure:

The imported submersible reflux pump with guide rod with automatic positioning fixed, sliding guide bar support as one of the whole water pump parts, generating all weight of the pumps as well as pump thrust all the role in the docking outlet pipe flange. Water pump, accessories and cables can work continuously for a long time without leakage under normal water depth.

Imported diving can move up and down for convenience. Inspection or maintenance personnel do not need to enter the bottom of the pool.

The reflux pump shall be a horizontal single stage structure with vertical single rail and self coupling mounting. The design of the impeller adopts no blocking and anti winding structure, and the motor and pump body are coaxial through solid particles with diameters of 100mm, 10kW and less.

The return pump can be automatically and securely coupled to the wall pipe and can slide from the top of the tank to the wall pipe at the direction of the guide rod.

The return pump is integrally designed, using closed connections and submersible, and all components of the pump include motors that operate continuously under water.

The impeller:

The impeller shall be made of stainless steel and used for dynamic balancing test. A locking device is arranged between the impeller and the shaft, which is used for preventing the operation from loosing, and the blade is designed as a three piece type. The utility model has the functions of self cleaning and vibration free, and the utility model is a design for the hydraulic transmission without clogging or winding.

The draft tube:

In order to maintain the hydraulic efficiency and reduce the energy consumption, a draft tube is arranged outside the impeller of the reflux pump, and the clearance between the impeller periphery and the draft tube is controlled.

The shaft and the bearing:

The shaft of the return pump and motor is a continuous shaft. The shaft can withstand all axial and radial loads that occur when the impeller rotates. The axis of the impeller is completely isolated from the pumping medium.

The reflux pump motor shaft in two permanently lubricated bearings on the rotating bearing for deep groove ball bearing, main bearing is a spherical ball bearing, wherein the inner bearing ball bearing is used to bear radial force, axial force of the bearing for a bear all by the main bearing.

The sealing of the pump shaft:

Each reflux pump has an oil chamber for the shaft seal system and is equipped with an oil drain device and an inspection screw hole. The oil drain and the check screw hole are easy to enter from outside, so that the oil change work is simpler and easier.

Each reflux pump shall have at least two seals to separate the pump parts.

The impeller wheel and the bearing are provided with two seals to prevent the life of the inner ring mechanical seal and play a protective role.

The seal at the end of the impeller shaft acts as an inserted static / moving ring double mechanical seal. Sealed in an oil chamber that is lubricated by a hydraulic action to overlap the sealing surface at a constant speed. Both internal and external mechanical seals are the latest products to prevent external liquids from entering the oil tank. Both internal and external mechanical seals operate independently.

The pump is used in the oil chamber of the shaft seal system to prevent the full space and the oil expansion in the design, and the leak proof sealing holes and inspection holes are easy to check and maintain from the outside.

The cooling system:

The return pump motor can be cooled sufficiently by the surrounding medium, the larger motor is equipped with an external cooling sleeve, and the back pressure of the pump liquid is used as the motor cycle cooling.

Lifting support system:

The reflux pump is provided with a hoisting hanger with seat and davit. Brake device for hoisting hoist.

Install the lifting support system includes a set of machine per square guide rail, and a special arm type davit, hand chain hoist.

The rigid support of the guide rod is at both ends. The lifting chain includes a water lift ring coupled to the pump.

Such self coupling system:

The water pump of the reflux pump is made of automatic coupling of the flange of the blue face and the through wall pipe, and the efficiency of the pump includes the water passing through the wall pipe. The coupling surface is sealed and reliable, and has self-cleaning function. The self coupling system is an export hard sealing type, and has reliable design guarantee, and the lifting and dropping can not be scratched and destroyed.

UK GRIMM Imported submersible return pump use condition:

1.Continuous operation, the medium temperature is not higher than 40 degrees;

2.Medium pH value of 6-9;

3.The maximum submergence depth 10m.

UK GRIMM Imported submersible return pump equipment features: 

1.According to the small head, large flow special design, high efficiency;

2.According to anti blocking, anti winding design, the use of reliable;

3.The use of the latest sealing materials, pumps can make the safety of continuous operation for more than 10000 hours;

4.Compact structure, easy installation and maintenance;

5.The main machine adopts stamping forming structure, small size, high precision, corrosion resistance, no noise;

6.The product set leakage, leakage and motor overload protection and alarm devices, to ensure product safety and reliability.

UK GRIMM Imported submersible return pump technical parameter:

Impeller diameter: 400-620mm

Nominal diameter: 400-600mm

Motor power: 1.5-22kw

Rated voltage: 380V

Rated frequency: 50HZ

Rated current: 4.1-76A

Protection level: IP68

Insulation class: F class

UK GRIMM Imported submersible return pump purpose:

       For surface drainage, pumping purified water; irrigation and control of the water system; recirculation or slurry pumping in wastewater treatment processes; requiring micro head and large flow locations.